Beryllium Copper Spring Finger Contact

Beryllium Copper Spring Finger Contact
Details:
A spring finger contact is a precision stamped elastic element that relies on controlled material hardness to maintain consistent contact force across repeated deflection. The standard grades are SUS301 SH spring stainless, 65Mn hardened and tempered steel, and C5191 phosphor bronze, with beryllium copper offered where the highest spring-back is required.
Send Inquiry
Description
Send Inquiry

4bfc9ce0-f5bb-4665-85cf-2b5fd5f057c7

 

A spring finger contact is a precision stamped elastic element that relies on controlled material hardness to maintain consistent contact force across repeated deflection. The standard grades are SUS301 SH spring stainless, 65Mn hardened and tempered steel, and C5191 phosphor bronze, with beryllium copper offered where the highest spring-back is required. Strip thickness runs from 0.1 mm to 1.5 mm, with the thinnest precision contacts produced at 0.1 mm. Hardness is held in the HV350-550 band so the contact arm deflects elastically without taking a permanent set, and the geometry is validated to 500,000 rebound cycles with permanent deformation limited to 0.02 mm; higher fatigue ratings of 800,000 or 1,000,000 cycles can be tuned for demanding assemblies. For conductive versions, a 5 um nickel layer keeps contact resistance below 50 m ohm, with gold or silver plating offered for lower-resistance joints. Each tip is chamfered to R0.2 and fully deburred so it cannot score the mating plastic housing during assembly, and the mating slot is designed around a 0.1-0.2 mm interference gap that can be adjusted to the tolerances of the paired part. Tooling covers snap contacts, conductive contacts and limit spring fingers as distinct contours, and the recoil amplitude itself can be tuned to the assembly rather than fixed to a standard travel.

 

For a spring finger, the failure buyers worry about most is loss of contact force after thousands of insertions - a fatigue problem that originates in tempering and stamping edge condition rather than in the raw material alone. Because we build from customer drawings and confirm with a sample first, the elastic arm length, free height and interference gap are tuned to the actual mating slot instead of a generic blank, so the measured spring force and travel match the assembly on the first production run rather than after several tooling rounds.

4379895a-501f-4af8-b5a8-890d4bb15bf8

Specifications

 

Parameter

Specification

Material

SUS301 SH / 65Mn hardened / C5191 phosphor bronze / beryllium copper

Thickness

0.1-1.5 mm (precision thin 0.1 mm)

Hardness

HV350-550

Fatigue life

500,000 cycles, permanent deformation <=0.02 mm (800k/1M upgradeable)

Conductive plating

Nickel 5 um, contact resistance <50 m ohm (gold/silver optional)

Tip chamfer

R0.2, deburred

Mating interference gap

0.1-0.2 mm

 

Applications

 

EMI/RFI shielding in equipment enclosures: the spring finger bridges metal seams with continuous grounding contact, which is why it is chosen over solid tabs where repeated access breaks the seam.

Battery and terminal contacts in appliances and electronics: nickel- or gold-plated contact points carry current without fretting, suiting low-voltage signal and power terminals.

Snap retention inside plastic housings: the chamfered, deburred arm inserts without scratching the housing, providing a repeatable latch in consumer and industrial assemblies.

 

Customization

 

Material grade substitution (stainless, spring steel, phosphor bronze, beryllium copper), thickness 0.1-1.5 mm, hardness tempering tuning, fatigue-cycle upgrade to 800,000 or 1,000,000 cycles, gold or silver low-resistance plating, and tooling for snap, conductive or limit spring-finger contours.

 

Packaging & Transportation

 

Small contacts are packed in individual anti-collision PE bags to preserve the plated contact surface. Each order is protected according to its product specification, inspected by dedicated staff, and supports third-party inspection. Shipped on EXW, FOB or DDP terms.

 

FAQ

 

Q: Can you provide a prototype or sample before mass production?

A: Yes, we provide a sample for confirmation before mass production.

Q: Do you provide free samples?

A: Yes, free samples can be discussed.

Q: Do you provide a warranty? If so, for how long?

A: Yes, a warranty is provided for about 3 months under normal storage conditions.

 

Hot Tags: beryllium copper spring finger contact, China beryllium copper spring finger contact manufacturers, suppliers, factory, galvanized steel stamping parts, metal stamping assemblies, precision metal stamping parts, stamped metal clips, stamped metal retainers, steel stamped components

Send Inquiry