Flat Stamped Sealing Shim Washer

Flat Stamped Sealing Shim Washer
Details:
Where mated components must meet a measured clearance, a flat stamped sealing shim washer sets that precise gap and keeps the fastening seated tight under vibration and load, instead of leaving the fit to guesswork. Purchasers look for a shim whose thickness stays consistent from piece to piece, slides onto the bolt without binding, and brings two surfaces to the designed clearance rather than compressing or loosening over time. Available in structural, stainless, copper or spring material, the flat, wave or locking form fills a measured space, seals a joint, and supports the bolted preload so the fastener holds under cyclic load. A plain, passivated or conductive finish matches the electrical or corrosion duty of the joint, and special ring, square or locating shapes are made to the buyer's own clearance. The washer exists to fine-tune axial clearance, keep a fastener from working loose, and provide a stable, concentric fit in precision and vibrating assemblies.
Send Inquiry
Description
Send Inquiry

Where mated components must meet a measured clearance, a flat stamped sealing shim washer sets that precise gap and keeps the fastening seated tight under vibration and load, instead of leaving the fit to guesswork. Purchasers look for a shim whose thickness stays consistent from piece to piece, slides onto the bolt without binding, and brings two surfaces to the designed clearance rather than compressing or loosening over time. Available in structural, stainless, copper or spring material, the flat, wave or locking form fills a measured space, seals a joint, and supports the bolted preload so the fastener holds under cyclic load. A plain, passivated or conductive finish matches the electrical or corrosion duty of the joint, and special ring, square or locating shapes are made to the buyer's own clearance. The washer exists to fine-tune axial clearance, keep a fastener from working loose, and provide a stable, concentric fit in precision and vibrating assemblies.

 

A shim washer that varies in thickness by more than a couple of hundredths of a millimetre defeats its own purpose, because the bolt either over-compresses or goes loose. Keeping die clearance and tooling condition stable holds the ±0.02 mm ultra-thin thickness and ≤0.05 mm coaxiality consistent across an entire batch, so a buyer can shim to a designed gap without sorting parts one by one. Tight batch control across the 0.05-2.0 mm range also lets one shim program cover both ultra-thin precision washers and standard load-bearing flat washers under the same quality standard, which simplifies stocking instead of sorting parts by hand before assembly.

 

Specifications

 

Parameter

Specification

Material

SPCC / SUS304 / pure copper / 65Mn; PTFE composite, aluminum options

Ultra-thin series

0.1 / 0.2 / 0.3 / 0.4 / 0.5 mm, thickness ±0.02 mm

Full range

0.05-2.0 mm custom

Types

Flat, wave, locking; special-shaped / combined structures

Hole / coaxiality

Inner hole +0.03/0; outer coaxiality ≤0.05 mm

Hardness

Flat HV180-220; spring HV300-380

Surface

Zinc / passivation / plain stainless; rust-resistant or conductive finishes

 

Applications

 

Precision instrument and bolted assemblies: the ±0.02 mm ultra-thin thickness lets a shim set exact axial clearance without micrometer-sorting every part.

Vibration-prone fastening: wave and locking washers at HV300-380 maintain pre-load and prevent loosening under cyclic load.

Conductive and corrosion-resistant joints: copper, passivated and stainless materials suit electrical contacts and exposed fastener points.

 

Customization

 

Thickness 0.05-2.0 mm, flat / wave / locking / special-shaped / combined structure, inner and outer diameter to bolt spec, hardness tempering, surface (zinc, passivation, plain stainless, conductive); ring / square / locating shims to your gap; OEM / ODM.

 

Packaging & Transportation

 

Thin washers are counted and bagged in controlled quantities to avoid scratching and mixing, then cartoned and palletized; a dedicated inspector verifies dimensions, with 100% inspection depending on the product. Trade terms: EXW, FOB or DDP.

 

FAQ

 

Q: Can you supply different washer types and materials together?

A: Yes. Flat, wave, locking and special-shaped shims in steel, stainless, copper or composite can be mixed within one order as agreed.

Q: How is quality guaranteed on precision shims?

A: A dedicated inspector checks each batch and we accept third-party inspection; inspection scope before packing depends on the product.

Q: What warranty do you provide?

A: We provide a warranty of about three months under normal storage conditions, handled by dedicated after-sales staff.

 

Hot Tags: flat stamped sealing shim washer, China flat stamped sealing shim washer manufacturers, suppliers, factory, aluminum stamped parts, metal stamping terminals, precision progressive stamping parts, precision stamped components, sheet metal stamping components, stamped metal terminals

Send Inquiry